Car ECU Programmer

  MST 90+ Auto Voltage Stabilizer for ECU Programmer User Manual The black line is connected to the negative pole The red line is connected to the positive pole Connect the charger power supply input line and battery charging line, Turn on the power supply The four indicator lights (ALARM, WORK, C-ERR, WARN) under the MST 90+ will flash at the same time once then go out together. If the MST-90 device does not detect the battery or the connection is incorrect, it means there is no voltage output. For this situation, you should connect it to the battery (or press the FORCE START button). When the [WORK] indicator light is on, it means the MST 90+ works normally. how to use MST 90+ Auto Voltage Stabilizer 3 Turn off the power at the same time, the ALARM and WARN indicator light will be on with the sound di di di. The output voltage is adjusted by the long press [MODE] button for 3 seconds. Press the [FORCE START] button to increase the voltage Press the [MODE] butt

Can CG FC200 calculate the checksum like KTAG ? Does it support virtual reading? Recently, many customers asked whether the  CG FC200 supports the checksum function. Yes, it will do checksum, but not all. User feedback 1: I did 17c50 and checksum did online…need wait for a 10seconds… have to check for VR User feedback 2: This tool doing checksum online…did at least 30 ecus…last is med17.1.6 with psa Everything is working. Actually, CG FC200 can clone over 500 ECUs like KTAG+ Kess, Kessy, Dimsport, etc. Car models are supported as below, press and hold ‘Ctrl+ F’ to query quickly. * Abarth, Aebi, Alfa Romeo, Alpina, Artec, Aston, Aston Martin, Audi * BMW, Baic, Bentley, Bugatti * CASE, CASE Tractors, Can-Am, Caterpillar, Chang An, Chery, Chevrolet, Chrysler, Citroen * DS, Dacia, Dallara, Deutz, Dodge, Ducati * FIAT, FODAY, Fendt, Ferrari, Force, Ford, Ford Trucks, Freightliner * GMC, Geely, Genesis Motors, Great Wall * Honda, Hyundai * Indian, Infiniti, Internation, Isuz

Is working with PSA Peugeot Citroen EDC17C60 in service mode? Will  PCMtuner kill it through service mode? It will not finish ECU. EDC17c60 works fine after manual change tprot. You must disable Tport manually. Our customers have made a few on the bench and no problem. Just had to turn off tprot with hex or OLS. If Tport is not disabled manually, Auto will not start after Write Flash. Here’s why: This is a known issue of the original pcmflash v1.20. PCMTuner 1.20 doesn’t know how to bypass PSA protection at the moment. pcmflash 1.21 fixes the issue with patch. Apparently with the current version you have to manually edit the otp area before writing. You need to edit tprot off manually. This is fix for DTC to try 2CDB78 => 0000 => 2CDB7C Patch for write protection or check here: ORI: 2D 0F 00 00 DF 32 04 80 1D C8 D6 A4 00 or 2D 0F 00 00 DF 32 04 80 1D C8 8E 83 00 TPROT OFF: 2D 0F 00 00 DF 32 04 80 00 00 00 00 00 Need change bit XX with 00 2D 0F 00 00 DF 32 04

  Welcome to the PCMtuner installation guide Preparation before installation: 1.Connect the device to the computer with power cable and USB cable, and plug the smart lock dongle into computer,like what I show you here . 2.Close all anti-virus software and firewall on the computer (the system firewall should also be closed. According to the system and software, Google how to close it if you dont know how to handle.) 3.Go to http://tuner-box.com download tool software Like this check below picture 4.unzip the downloaded software check below 5.then you will get 3 files like below Hmmm,you need read the notice before start install all software Then click PCM_Setup run it like below Notice , never select lauch software Continiue click here Till happen this Pcmturner-Software-install-10 So cool When you see below things happen ,that’s mean you already completely install tool software Pls read the carefully what the software tell you When you finish install , then

V1.21 PCMtuner is the 2022 newest  ECU Programmer It can read & write ECU data by OBD, BENCH, and BOOT modes. Perform a complete backup of ECU data, easy ECUs clones, and power upgrades. Compared with the V1.20, it newly added 44 new protocols, Bosch ECU read/write protocols without opening the cover. Here is a list of questions for your reference. Q: What other functions can PCMtuner do besides reading and writing ECU? A: All functions supported are in the following list. *  Read and write data via OBD/BENCH/BOOT mode *  ECU clone *  ECU parameter adjustment *  ECU maintenance engineering *  Chip tuning *  Read ECU maps *  Checksum correction *  Stage1-3, gearbox tuning , LC, sportdisplay , immo off, adblue off, dpf off, dtc off , vmax , swirl off *  Read flash and ep files *  Powertrain adjustment *  Support online update *  VR files  supply *  Pinout comewith *  Helpdesk and tuner account *  OBD2 reading *  Cover-free wielding-free no disassembly data re

Recently,we have customers asking whether  PCMtuner will read and write VAG Simos PCR2.1 by OBD or Bank. Here comes the official answer from PCMTuner Technical Support. OBD only after unlock in BSL mode, like described and like original PCM flash. BSL unlock it, then OBD read it. If some don’t have password, then can direct obd read it. Module 57 1) Check the current lock status with ECU in the car, if the check is disabled, you can go to read-write. otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection (PCR2.1) and unlock. Reading writing can be done with ECU in car. bsl – open ecu, connect resistors Linked vehicles: · 2.8L V6 FSI (SIMOS8.1) – Reading, writing, checksum correction. · 3.2L V6 FSI (SIMOS8.2) – Reading, writing, checksum correction. · 3.0L V6 TFSI (SIMOS8.3) – Virtual reading, writing, checksum correction. · 3.0L V6 TFSI (SIMOS8.4) – Virtual reading, writing, checksum correction

IS  PCMtuner Better than KTM200 ? Maybe a lot of people have questions about this, I just received PCMTuner recently, I would like to share it with you. I have seen many Chinese websites selling it online. It looks so funny, can read and write ECU, also download VR files. After comparing it with many dealers, I finally bought it from autonumen.com. Nice hardware overall and looks better than the KTM with a GPT board. I installed the software pcmtuner 1.21 and everything is fine. I also registered it and asked my dealer to activate it. After activation I have two accounts, one is for visiting pcmtuner official website, another is tuner account for viewing vz performance system. I tested this PCMTUNER ECU programmer. If he does everything that the description says, he’s really good. I have many different devices. It is much faster to read and write compared to the Russian Trasdata. It can also clone edc17 drivers by bank. Trasdata does not clone all drivers. If the device

There are 2 possibilities for canbus on these ECUs. You must use a capacitor on Iveco edc17c49 even with the original pcmflash and scanmatik (capacitor 10uf must be used for gpt1). Always fix is a capacitor in serial with GPT1 10uF or 100uF and extra ground at pin 21. Bosch EDC17C69 ecu pinout diagram Bosch EDC17C49 ecu pinout diagram How to read Iveco EDC17C49 with PCMTuner without opening ECU? Set up pcmtuner usb dongle, hardware and ECU connection following the wiring diagram above In PCMTuner software, select Iveco- Daily- EDC17C49- Bench mode Check instructions and make bench connection Then press Read and Write Use module [71] Bosch MEDC17 (TC1724/1728/1767/1782/1784/1797) FLASH Read data until completed If you want to know more about ECU Programming Tools , please visit our website www.obd2tool.com

Question: I wonder if the pcmtuner is more reliable than a kess v2 clone ? Here’s the clue. It is like a tool of 2020 vs 2005. There is not enough going back. *   Kess v2 v5.017 clone = old cars, old protocols, less support, hardware need reworked. *   Kess V2 just OBD, less of CAN and Boot mode. *   Pcmtuner = modern cars, good support, updates, good hardware. *   PCMTuner supports OBD, Bench and Boot 3 modes. *   Kess v2 clone no update *   PCMTuner is upgradable, the next update will be MG1 MD1 though release date TBC. They have a plug work with pcmtuner hardware, you can update in your old pcm tuner. Reference: Kess v2 ksuite car list (without upgrade) PCMTuner car and chip list (keep updating) We have customers feedback the pcm tuner works well very, can support most of ECUs, never crash, all professional, fast, quick support, total available to help by Teamviewer online support or technical support in WhatsApp app. The software is the same as the original pcmf

Recently a customer encountered some problems using iprog+ pro clone : ​​when the firewall and windows defender were turned off, I have to wait many seconds between switching scripts (sometimes I have to wait a minute before starting the next script use, or wait for the program to open – it seems that sometimes the programmer cannot be found or the system is looking for it, but the connection to the Windows system is not disconnected). On Windows 7 it works perfectly. Where is the problem? Updated: I have check two times that real-time protection is disabled by the DefenderControl program. I have disabled also in Regedit: (Windows Defender Security Center Service) HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SecurityHealthService (Security Center service) HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\wscsvc Start DWORD 2 = Enable 4 = Disable HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows Defender DisableAntiSpyware Modify = 1 HKEY_LOCAL_MACHIN

  Problem: I just received one new  CG FC200 ECU Programmer last week. After installing the FC200 software, I started to run the software, but I encountered three errors. Error 1: e126: Failed to open the device, please check the device connection Error 2: Failed to connect to the server. Check the network or try again later Error 3: There is no authorization information displayed on the screen. Cnautotool.com technician replied: For error 1, the possible cause is that the device is not detected out. Suggestion: Try on other USB ports For error 2& error 3, please check if the network has been connected normally. Then go to try again.