How to connect pcmtuner/pcmflash to Iveco Bosch EDC17C69/EDC17C49 ECUs?

There are 2 possibilities for canbus on these ECUs. You must use a capacitor on Iveco edc17c49 even with the original pcmflash and scanmatik (capacitor 10uf must be used for gpt1).

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-1

Always fix is a capacitor in serial with GPT1 10uF or 100uF and extra ground at pin 21.

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-2

Bosch EDC17C69 ecu pinout diagram

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-3

Bosch EDC17C49 ecu pinout diagram

How to read Iveco EDC17C49 with PCMTuner without opening ECU?

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-4

Set up pcmtuner usb dongle, hardware and ECU connection following the wiring diagram above

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-5

In PCMTuner software, select Iveco- Daily- EDC17C49- Bench mode

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-6
How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-7
How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-8

Check instructions and make bench connection

Then press Read and Write

Use module [71] Bosch MEDC17 (TC1724/1728/1767/1782/1784/1797) FLASH

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-9
How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-10
How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-11

Read data until completed

How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-12
How-to-connect-pcmtuner-pcmflash-to-Iveco-Bosch-EDC17C69-EDC17C49-ECUs-13

If you want to know more about ECU Programming Tools , please visit our website www.obd2tool.com

评论

发表评论

此博客中的热门博文

How to Read and Write ECU Safely thru OBD with KESS ECU Programmer?

图片
KESS V2 V5.017 Introduction: Kess V2 V5.017 can read and write ECU via OBD2 port directly, no need to disassemble the ECU from the car. The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write.   Here’s the  step ： STEP 1:  Plug KESS into car’s OBD-II port   STEP 2:  Plug KESS into laptop’s USB port   STEP 3: Launch KESS software   STEP 4: Read/Write data to vehicles EEPROM ECU chip   What’s more, tuning/remapping is completely safe because you can backup and restore original ECU data back to car in 1-click. MPPS is a very good tool and has Tricore support, but you need to open the ECU first as with KTAG .   Example: read ECU in my 2011 VW Scirocco with MPPS v18 If you don’t feel comfortable to open an ECU and connect with pogo pins using KTAG/MPPS, you c
阅读全文

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

图片
  This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.   To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.   Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.   Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.   BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERMS AND CONDITIONS, YOU RELIEVE US F
阅读全文

Is Possible Clone MD1CS006 Renault with Hexprog

图片
Is it possible clone md1cs006 Renault with Microtronik HexTag Programmer ? Yes its supported for read and write. Please check the supported list from below table: Moreover, Microtronik HexTag can read and write more ECU including: Abarth , Alfa Romeo, Alpina, Aston Martin, Audi, Baic, Bentley, BMW, Buick, Chery, Chevrolet, Chrysler, Citroen, Cupra, Dacia, Daewoo, Dodge, Dongfeng, Donkervoort, Effedi, Ferrari, Fiat, Ford, Geely, Holden, Honda, Hyundai, Infiniti, Isuzi, Jaguar,Jeep, JMC, Kia, Lamborghini, Lancia, Landrover, Lincoln, Maserati, Mazda, McLaren, Mercedes Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Rolls Royce, Saab, Saic, Saturn, Seat, Skoda, Smart, Subaru, Suzuki, Toyota, Vauxhall, VW, Volvo etc. Please view Microtronik HexTag ECU tuning list from the below link: http://forobd2tool.com/wp-content/download/Microtronik-HexTag-ECU-tuning-list.pdf
阅读全文