PCMtuner Software installation method

 

Welcome to the PCMtuner installation guide Preparation before installation:
1.Connect the device to the computer with power cable and USB cable, and plug the smart lock dongle into computer,like what I show you here .

2.Close all anti-virus software and firewall on the computer (the system firewall should also be closed. According to the system and software, Google how to close it if you dont know how to handle.)

3.Go to http://tuner-box.com download tool software

Like this check below picture

4.unzip the downloaded software check below

5.then you will get 3 files like below

Hmmm,you need read the notice before start install all software Then click PCM_Setup run it like below




Notice , never select lauch software
Continiue click here

Till happen this

Pcmturner-Software-install-10

So cool
When you see below things happen ,that’s mean you already completely install tool software
Pls read the carefully what the software tell you

When you finish install , then run PCMtuner software And register it like below

When register , pls contact your seller help you active it ,Monday-Friday will work When your seller help you active it pls check like below



Btw, all tool user have a support account to Go to here login http://tuner-box.com/login

User name is your register email , password is your tool S/N

When tool software install done , you need go to install tuner account software

That’s mean VZperformance software , Like this one

If you don’t want to install this , you can direct to go to https://support.vz-performance.com

How can we get this user name and password

Once your order our tool , pls contact your seller help you creat one , then you can use this accout

When you get user name and password you can login Like below

If you want to get VR files, or WinOLS damaos or A2L file, just click search function ,then type what you want

Like below

At this account , you also can request chiptuning , like stage1-stage3 , popbangs, adblue , dpf ,etc, just need creat ticket ,but its pay item , you can contact your seller about the charge .

Thank you so patience read above all , enjoy your tool now ,and work with us .

评论

发表评论

此博客中的热门博文

How to Read and Write ECU Safely thru OBD with KESS ECU Programmer?

图片
KESS V2 V5.017 Introduction: Kess V2 V5.017 can read and write ECU via OBD2 port directly, no need to disassemble the ECU from the car. The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write.   Here’s the  step ： STEP 1:  Plug KESS into car’s OBD-II port   STEP 2:  Plug KESS into laptop’s USB port   STEP 3: Launch KESS software   STEP 4: Read/Write data to vehicles EEPROM ECU chip   What’s more, tuning/remapping is completely safe because you can backup and restore original ECU data back to car in 1-click. MPPS is a very good tool and has Tricore support, but you need to open the ECU first as with KTAG .   Example: read ECU in my 2011 VW Scirocco with MPPS v18 If you don’t feel comfortable to open an ECU and connect with pogo pins using KTAG/MPPS, you c
阅读全文

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

图片
  This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.   To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.   Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.   Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.   BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERMS AND CONDITIONS, YOU RELIEVE US F
阅读全文

Is Possible Clone MD1CS006 Renault with Hexprog

图片
Is it possible clone md1cs006 Renault with Microtronik HexTag Programmer ? Yes its supported for read and write. Please check the supported list from below table: Moreover, Microtronik HexTag can read and write more ECU including: Abarth , Alfa Romeo, Alpina, Aston Martin, Audi, Baic, Bentley, BMW, Buick, Chery, Chevrolet, Chrysler, Citroen, Cupra, Dacia, Daewoo, Dodge, Dongfeng, Donkervoort, Effedi, Ferrari, Fiat, Ford, Geely, Holden, Honda, Hyundai, Infiniti, Isuzi, Jaguar,Jeep, JMC, Kia, Lamborghini, Lancia, Landrover, Lincoln, Maserati, Mazda, McLaren, Mercedes Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Rolls Royce, Saab, Saic, Saturn, Seat, Skoda, Smart, Subaru, Suzuki, Toyota, Vauxhall, VW, Volvo etc. Please view Microtronik HexTag ECU tuning list from the below link: http://forobd2tool.com/wp-content/download/Microtronik-HexTag-ECU-tuning-list.pdf
阅读全文