PCMtuner ECU programmer successfully read AUDI A3 Bosch MED17.5 TC1766

It has been tested and confirmed by OBD2.LTD engineer that PCMtuner ECU Programmer can read AUDI A3 1800 TFSI 160 2006-2016 Bosch MED17.5 TC1766 on Bench successfully.

What you should do before operation:

You need to install PCMtuner V1.21 software package on your computer (Win7 or Win10). The Scamatik Setup Wizard, Guardant Drivers, pcmtuner software and pcmflash software are included in the PCMtuner software package.

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-1

Don’t install other software on t on PCMtuner, otherwise the device will be locked, and this damage is not covered by the warranty.

After installation, you need to register a PCMTUNER software account

Complete user registration with the full name, company name, email, phone and country, and submit it. Remember to offer your email to our customer service to help you activate the account. (Reference: PCMTuner V1.21 Software Download + Driver Installation Guide)

When the Tuner account is activated, it’s ready to use the pcmtuner software.

Open PCM Tuner software

Click ECU OPERATIONS>> VEHICLE TYPE>> Volkswagen

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-2

Input MED17.5 in the search box to search the ECU model quickly

Find out Audi-A3-1800 TFSI (160 hp), then click ‘Show’

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-3

Click ‘BENCH’

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-4

You can click instructions to see the method, operation difficulty, checksum, collaboration file size and backup.

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-11
PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-5

Pull down the page, and you can see the wiring diagram and operation steps.

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-6

Then click ‘READ and WRITE’

When it prompts ‘An updated version was found on the server. Would you like to download build 1.2.5 releases on 2022-02-20?”, just click ‘No’ to continue.

It will enter PCMflash software

Click ‘Settings’ to select the language you need. It only supports English and Russian so far.

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-7

Select ECU: [71] Bosch: MEDC17 (TC1762/1766/1792/1796) EEPROM

Click ‘Identification’ to detect the ECU info

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-8

Then click ‘Read’ to read ECU data

During the operation, it will ask “Would you like to use automatic power control (L-line)?”, just click ‘Yes’ to continue.

After reading the data successfully, save it.

PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-9
PCMtuner-ECU-programmer-successfully-read-AUDI-A3-Bosch-MED17.5-TC1766-10

Done!

评论

发表评论

此博客中的热门博文

How to Read and Write ECU Safely thru OBD with KESS ECU Programmer?

图片
KESS V2 V5.017 Introduction: Kess V2 V5.017 can read and write ECU via OBD2 port directly, no need to disassemble the ECU from the car. The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write.   Here’s the  step ： STEP 1:  Plug KESS into car’s OBD-II port   STEP 2:  Plug KESS into laptop’s USB port   STEP 3: Launch KESS software   STEP 4: Read/Write data to vehicles EEPROM ECU chip   What’s more, tuning/remapping is completely safe because you can backup and restore original ECU data back to car in 1-click. MPPS is a very good tool and has Tricore support, but you need to open the ECU first as with KTAG .   Example: read ECU in my 2011 VW Scirocco with MPPS v18 If you don’t feel comfortable to open an ECU and connect with pogo pins using KTAG/MPPS, you c
阅读全文

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

图片
  This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.   To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.   Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.   Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.   BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERMS AND CONDITIONS, YOU RELIEVE US F
阅读全文

Is Possible Clone MD1CS006 Renault with Hexprog

图片
Is it possible clone md1cs006 Renault with Microtronik HexTag Programmer ? Yes its supported for read and write. Please check the supported list from below table: Moreover, Microtronik HexTag can read and write more ECU including: Abarth , Alfa Romeo, Alpina, Aston Martin, Audi, Baic, Bentley, BMW, Buick, Chery, Chevrolet, Chrysler, Citroen, Cupra, Dacia, Daewoo, Dodge, Dongfeng, Donkervoort, Effedi, Ferrari, Fiat, Ford, Geely, Holden, Honda, Hyundai, Infiniti, Isuzi, Jaguar,Jeep, JMC, Kia, Lamborghini, Lancia, Landrover, Lincoln, Maserati, Mazda, McLaren, Mercedes Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Rolls Royce, Saab, Saic, Saturn, Seat, Skoda, Smart, Subaru, Suzuki, Toyota, Vauxhall, VW, Volvo etc. Please view Microtronik HexTag ECU tuning list from the below link: http://forobd2tool.com/wp-content/download/Microtronik-HexTag-ECU-tuning-list.pdf
阅读全文