CG FC-200 V1.0.5.0 Update

 

Best ECU Tool CG FC200 V1.0.5.0 Re-released on February 28, 2022. The CG FC-200 new update add Turkish language and add Bosch engine computer BOOT mode and Bosch engine computer bank mode.

CG-FC-200-V1.0.5.0-Update

V1.0.5.0 Detail update information:
1. Add Turkish language version
2. Added BOOT mode of bosch engine computer
ME17.5.26
ME17.8.32
ME17.9.1
ME17.8.61
MED17.8.31
MED17.9.8
MED17C17.9
MED17C81
3. Added Bosch engine computer Bench Mode
ME17.7.8
ME17.9.1
MED17.8.2
MED17.9.8
EDC17C45
4. Bug fixed and Software performance improved

评论

发表评论

此博客中的热门博文

How to Read and Write ECU Safely thru OBD with KESS ECU Programmer?

图片
KESS V2 V5.017 Introduction: Kess V2 V5.017 can read and write ECU via OBD2 port directly, no need to disassemble the ECU from the car. The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write.   Here’s the  step ： STEP 1:  Plug KESS into car’s OBD-II port   STEP 2:  Plug KESS into laptop’s USB port   STEP 3: Launch KESS software   STEP 4: Read/Write data to vehicles EEPROM ECU chip   What’s more, tuning/remapping is completely safe because you can backup and restore original ECU data back to car in 1-click. MPPS is a very good tool and has Tricore support, but you need to open the ECU first as with KTAG .   Example: read ECU in my 2011 VW Scirocco with MPPS v18 If you don’t feel comfortable to open an ECU and c...
阅读全文

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

图片
  This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.   To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.   Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.   Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.   BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERM...
阅读全文

Where to download PCMtuner V1.21 Software? How to install

图片
Where to download  PCMtuner V1.21 Software? How to install? Go ahead to read this post. 1.PCMTuner V1.21 Software Download PCMTuner ECU programmer comes with CD of V1.21 software, just send it to your computer and install. You also can download the software from our link or the official website. 21 PCMTuner software free download link: https://share.weiyun.com/7QqH2WLw Password: irbk5u Size: 508.28MB Note: it has been tested 100% working by  Obd2tool.com engineer. Download from the PCMTuner official website Access https://www.tuner-box.com/ Click ‘Download’ at the top of the website When it pops up Download Software window, enter the email address, select the country and enter your telephone number. Language: English, Russian Operating system: Win7, Win10 Kindly notice: *   PCMtuner is not compatible with other software (such as pcmflash, gurandant driver, scanmatick), do not use them on PCMtuner, otherwise the device will be locked (for this, we...
阅读全文