CG FC-200 ECU Programmer FAQs

Q: Does FC200 support offline?

A: No. Using the FC200 requires an Internet connection and 12V power.

Q: Will CG FC200 support Italian?

A: It only supports English, French, Spanish, Polish, Traditional Chinese and Simplified Chinese so far. But you can contact our customer service to provide the requirement.

Q: Can I choose mode 1 to test BMW MSV90 TC1796 by CG FC200? Using the STD cable to do PIN diagram or must connect by the professional harness as shown in the following pic?

CG-FC-200-ECU-Programmer-FAQs-2

Q: Are there any other fees besides the upgrade fee?

A: No need. CG FC200 supports free update online for One Year. The annual fee will be $125/year after the first year.

A: You must use the FC200 Adapters (Vehicle-grade wiring harness) to do.

Q: Can FC200 read vag simos 10.22 (skoda fabia 1.2)?

CG-FC-200-ECU-Programmer-FAQs-3

A: No, it doesn’t support so far.

Q: Does FC200 support ECU programming on 2018 Clio Benziner?

A: No, it doesn’t support so far. Only supports reading and writing data.

Q: Does FC200 support DCM 6.2 VAG?

A: No, it doesn’t support so far.

Collection of CG FC-200 ECU Programmer Common Question and Answers

Q: Will the following prompt appear when the CG FC200 Auto ECU Programmer is first time to use?

‘A new device is detected, and you can enjoy 1 year of free after-sales service after activation. Do you want to activate it immediately?’

CG-FC-200-ECU-Programmer-FAQs-1

A: Yes. All new FC200 ECU programmers will appear this message for the first time to use. Just click ‘activate’ to continue.

评论

发表评论

此博客中的热门博文

How to Read and Write ECU Safely thru OBD with KESS ECU Programmer?

图片
KESS V2 V5.017 Introduction: Kess V2 V5.017 can read and write ECU via OBD2 port directly, no need to disassemble the ECU from the car. The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write.   Here’s the  step ： STEP 1:  Plug KESS into car’s OBD-II port   STEP 2:  Plug KESS into laptop’s USB port   STEP 3: Launch KESS software   STEP 4: Read/Write data to vehicles EEPROM ECU chip   What’s more, tuning/remapping is completely safe because you can backup and restore original ECU data back to car in 1-click. MPPS is a very good tool and has Tricore support, but you need to open the ECU first as with KTAG .   Example: read ECU in my 2011 VW Scirocco with MPPS v18 If you don’t feel comfortable to open an ECU and c...
阅读全文

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

图片
  This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.   To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.   Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.   Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.   BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERM...
阅读全文

CGDI FC200 ECU Programmer use tips

图片
CGDI FC200 professional ECU programmer is designed for ECU/ EGS clones, which supports data processing, ISN read and write, disassembly matching, VIN modification, and DTC shielding, etc. This article will share the use tips on Device Search Function, Data Backup & Restore when using CGDI FC200 ECU Programmer. Part 1. Use tips on Device search function (1)ECU search (2)Bosch number search (3)Bosch number query (click “Bosch search”) Part 2. Use tips on Data Backup Click “Backup Data” to back up the ECU data. After reading, please save the data for subsequent use. Note: This operation needs to be connected to the network. Please ensure that the network is normal during use. Part 3. Use tips on Data Restore Click “Restore Data” to write the ECU data. Before writing, please make sure the data is backed up. The restored data will overwrite the current ECU data. The data can be the data of the current ECU or other ECU of the same type. Please have your attention...
阅读全文