How to Solve Xprog 6.12 Failed to install Driver Software on Win7

 

I have an xprog 6.12 ecu programmer. I close the internet, firewall and all antivirus software on my computer and already install Adobe. When I connect the xprog-box programmer, the system tells me that Windows encountered a problem installing the driver software for my xprog, the system cannot find the file specified. It’s Win7. How to fix this problem?

Xprog-6.12-Failed-to-install-Driver-Software-on-Win7-Solution

Obd2tool.com chief engineer gives the advice:
Check whether the driver is installed.

4 steps to install XPROG V6.12 software:
*   Click the file “installation.reg”, get the file information to the regedit.
*   The file “AdbeRdr11000_zh_CN.exe” must be installed, otherwise the Xprog software will fail to start.
*   Plug the Xprog main interface into the computer and install the USB driver.
*   Copy the folder “XPROG-BOX6.12” to the desktop, open it, and run the “xprogdesktop.exe”, then open the software.

Windows system required as below:
Operating system: WinXP/ Win7/ Win8
1. Windows system should be windows XP 32bit OR windows 7 64 bit, all the patch software for the windows system should be installed already and the windows properly works well.
2. The windows system should be with at least 2 partitions (except the CD ROM.)
3. Can not be working with the virtual hard disk.

Important to know!!!
*   XPROG V6.12 dongle isn’t compatible with the older version Xprog.
*   Please close all anti-virus software on your computer, because the anti-virus software will kill Xprog V6.12 driver.
*   Disconnect internet. If not, the internet may damage XPROG hardware.
*   Uninstall all the old version XPROG software before you install V6.12 software because XPROG V6.12 hardware is not compatible with other versions of XPROG software.
*   Never try to UPDATE it, the hardware will be damaged if you try to update it online.

评论

发表评论

此博客中的热门博文

How to Read and Write ECU Safely thru OBD with KESS ECU Programmer?

图片
KESS V2 V5.017 Introduction: Kess V2 V5.017 can read and write ECU via OBD2 port directly, no need to disassemble the ECU from the car. The problem with some ECU’s, is that you can’t read them over OBD (except on some original/high priced tools) and for that reason you may need KTAG to read a full BDM, unlock TPROT (if it’s available), write the modifications back with KTAG and then you can use KESS over OBD to read/write.   Here’s the  step ： STEP 1:  Plug KESS into car’s OBD-II port   STEP 2:  Plug KESS into laptop’s USB port   STEP 3: Launch KESS software   STEP 4: Read/Write data to vehicles EEPROM ECU chip   What’s more, tuning/remapping is completely safe because you can backup and restore original ECU data back to car in 1-click. MPPS is a very good tool and has Tricore support, but you need to open the ECU first as with KTAG .   Example: read ECU in my 2011 VW Scirocco with MPPS v18 If you don’t feel comfortable to open an ECU and connect with pogo pins using KTAG/MPPS, you c
阅读全文

Instruction about Reading and Writing on Volvo GPT vehicles with KTAG ECU Programmer.

图片
  This is a Ktag help file used for Volvo Bosch EDC17 on GPT vehicles.   To use this protocol of communication you have to remove and open the ECU. It is a risky operation, to be done with great care and caution to avoid damaging the ECU beyond repair.   After opening the ECU and before proceeding with reading and/or programming, you are strongly advised to reconnect the unit to the vehicle and start the engine, to make sure it still works.   To use this protocol you also need to connect to the ECU connector through a cable, and solder one or more wires to the programming pads.   Incorrect or poorly made connections and solderings may damage the ECU, often beyond repair.   Under no circumstances we shall be liable for any damage caused to the ECU during the opening, due to connections and soldering that do not comply with the instructions provided in this manual.   BY USING THIS PROTOCOL, YOU CONFIRM YOUR FULL AND UNCONDITIONAL ACCEPTANCE OF THIS TERMS AND CONDITIONS, YOU RELIEVE US F
阅读全文

Is Possible Clone MD1CS006 Renault with Hexprog

图片
Is it possible clone md1cs006 Renault with Microtronik HexTag Programmer ? Yes its supported for read and write. Please check the supported list from below table: Moreover, Microtronik HexTag can read and write more ECU including: Abarth , Alfa Romeo, Alpina, Aston Martin, Audi, Baic, Bentley, BMW, Buick, Chery, Chevrolet, Chrysler, Citroen, Cupra, Dacia, Daewoo, Dodge, Dongfeng, Donkervoort, Effedi, Ferrari, Fiat, Ford, Geely, Holden, Honda, Hyundai, Infiniti, Isuzi, Jaguar,Jeep, JMC, Kia, Lamborghini, Lancia, Landrover, Lincoln, Maserati, Mazda, McLaren, Mercedes Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Rolls Royce, Saab, Saic, Saturn, Seat, Skoda, Smart, Subaru, Suzuki, Toyota, Vauxhall, VW, Volvo etc. Please view Microtronik HexTag ECU tuning list from the below link: http://forobd2tool.com/wp-content/download/Microtronik-HexTag-ECU-tuning-list.pdf
阅读全文